- Which of the following correctly discribes the characteristics of switched and routed data flows. - A Switches create a single collision domain and a single broadcast domain, Routers provide seperate collision domains.. - B Switches create seperate collision domains and seperate broadcast domains, Routers provide seperate collision domains and seperate broadcast domain as well.. - C Switches create seperate collision domains and seperate broadcast domains, Routers provide seperate collision domains.. - E Switches create seperate collision domains and a single broadcast domain, Routers provide seperate broadcast domain.. - Which of the following are examples of the datalink layer (Choose 2. - Which of the following is a true statement about the function of a bridge ? A A bridge creates or maintains a table of the ava ilable routes and their conditions.. - D A bridge creates or maintains a table of the IP addresses of the hosts connected to it’s network segment.. - A Decrease the number of collision domains. - E Increase the number of collision domains. - Giving the following description of OSI layers, choose the correct order that these statements are listed in.. - III This layer provides the physical transmission of the data and handles error notification and flow control.. - A Define the number of access lists supported on the interface B One-by-one copy the access list to the selected interfaces C Choose an interface to apply to the access list group. - D Define the access list number along with additional parameters E Assign th access list number to an access list group.. - F Define an access list group with both the access list number interface number as members.. - Which of the following best describes the meaning of “ show access- list 101. - A Verifies your 101th access list. - B Shows extended access list 101 C Verifies your access lists D Monitors IP access lists. - E Shows the access- list error message 101. - What does the term “backoff” refer to on an Ethernet network ? A It is a node or software program that supplies services to a front-end.. - B It is a node or software program that supplies services to a back-end.. - C It is the length of time a device has to wait after an collision on an Ethernet network before trying to send another message.. - D It is a type of network protocol that allows nodes to centend for network access.. - E It is the part of the network that provides the primary path for traffic sent to and from other networks. - FastEthernet compares to 10baseT Ethernet in which of the following ways (Choose 4). - D Both FastEthernet and 10BaseT Etherne t uses the same MTU E FastEthernet is an extension of the IEEE 802.3 specification. - You are required to load a new version of the cisco IOS into one of the routers on your company’s corporate network. - Which of the following command will. - You are configuring a router from setup mode. - You are configuring a Cisco router that is attached to your company’s corporate internetwork. - Which of the following is responsible for storing the ARP cache, routing tables and packet buffers.. - Which of the following symbols in the router prompt indicates that you are in privileged mode. - You are configuring an cisco switch. - How can you get help on the command that you are trying to enter. - How do you view all acces list applied on all interfaces (Choose 2. - A show access list. - B show running config C show access list all. - D show access list interfaces all. - What is sure about IPX rip (Choose 2. - What is the following term called : The process in which frames from one network system are placed inside the frames of another network system ? A Route Poisoning. - What is the broadcast address in a 802.3/LAN A 0.0.0.0. - How do you configure the line console password to “cisco. - You are required to backup yo ur IOS to an network location.. - Which of the following command will accomplish this. - Which command will show you the configuration of the system hardware, the best software version, the names and sources of configuration files and the best image. - Which of the two Ethernet implementation have distances of 100 Meters ? A 10 base 2. - What command will enable an encrypted password which cannot be seen in clear text in the running config. - What command will you give on the privileged mode to see the previous 10 commands in your buffer. - What command will enable a network on an interface ? A Ip network 10.1.2.0. - What command will you enter to make a subinterface on serial 0 ? A 1 and 2. - You want a message to appear at an interface defining the job description of the network attached finance lan . - How do you accomplish this. - You can config ppp on which of the following physical interfaces (Choose 2. - Which command do you use to disable CDP on a given interface ? A (config)# no CDP run. - To suspend a telnet session, what command do you enter ? A exit. - What command check layer 3 connectivity ? A telnet. - What command wil force the router to boot from ROM ? A Boot rom. - What statement is true regarding CDP ? A it is disabled by default. - What is a root port ? A A root bridge. - C It is the lowest cost path from the non-root bridge to the root bridge. - To reset the configuration revision number, what command do you use in privileged mode. - What port is the port no of TFTP ? A 23. - What is a 3 way handshake. - You are given an ip adress what subnet is the host ip on ? A . - How do you prevent routing loops in a routed network (Choose 2) A Split Horizon. - Which of the following is an IP link state protocol ? A RIP. - What is sure about RIP version 1 (Choose 2. - D it is a classfull routing protocol. - What command will display all ip routing protocol A show all protocol. - How do you apply an accesslist on an interface ? A I access list in/out. - What is the range of the extended ip accesslist ? A 1-99. - A Access list 101 permit any any. - B Access list 1 deny C Access list 1 deny . - What command displays the sap table ? A show sap table. - What command shows the encapsulation type, LMI, DLCI on an interface S0 ? A Show frame relay. - Based on addres what is the protocol and type of adress ? A Mac and multicast. - B Ip and Multicast C Ip and broadcast D None of the above. - The Following questions are not complete but they are very usefull for the CCNA exam , I had several of them. - How do you configure RIP routing. - What is special about this ? 85. - What do you need for efficient routing. - What is the effect of having the following access- list on interface e0 ? ACCESS-LIST 800 PERMIT 3D 4A. - In IPX addessing, how is the node part specified. - How do you configure IGRP on a router with an administrative distance of 100. - What is the defination of CIR. - The destination address of the incoming packet 86. - it is implied (It’s the MAC address) 93. - Create an static mapping of the next hop address with the DLCI 95
Xem thử không khả dụng, vui lòng xem tại trang nguồn hoặc xem
Tóm tắt