Có 60+ tài liệu thuộc chủ đề "kỹ thuật gấp giấy"
tailieu.vn Xem trực tuyến Tải xuống
After that turn model inside out. See diagrams 6 and 7 for the result.. Don’t push flat. they will flatten automatically in diagram 11..13!. QQ 8Fold point down. Q Q 9Fold two flaps so that they will overlap. See diagram 14 for the position of the wings. Turn model over.. Points Q flatten automatically.. Turn model over.14 15Fold upper edges...
tailieu.vn Xem trực tuyến Tải xuống
Designed in 4/97 and diagrammed in 5/97;. Fold and unfold 3. Fold and unfold left side
tailieu.vn Xem trực tuyến Tải xuống
“One-Way” Arrow. All Rights Reserved A dollar bill makes a model 100mm long and 32mm wide.. Rectangles of other dimensions may also used, provided they are “considerably” longer than they are wide.. Start with the “ONE” side up. Crease at eights, but not sharply on the middle crease.. Turn over and rotate 1/4 either way (depending on which way you...
tailieu.vn Xem trực tuyến Tải xuống
Then use “A” and the center vertical line to make crease “B”, at the same distance. Flip down the top eighth, squashing the corner at the right.. Reverse-fold on existing crease. Reverse-fold on the crease. Reverse-fold at the top,. closed-sink at the bottom. Reverse-fold. Reverse-fold the middle triangle upwards.. Reverse-fold the top point down, tucking the tip into the pocket...
tailieu.vn Xem trực tuyến Tải xuống
Inside reverse folds. Make 4 inside reverse folds
tailieu.vn Xem trực tuyến Tải xuống
Balloon with basket Maarten van Gelder 1992 Aug. Balloon with basket Maarten van Gelder 1992 Aug
tailieu.vn Xem trực tuyến Tải xuống
Diagrammed by R.Glynn © February 1999. Fold the point up inside the model (you need to pull the model apart. Repeat steps 3-8 on this side. Fold the point up inside the model (much harder than step 7!). Swivel the point to the. Diagrammed by R.Glynn © February 1999 21. Repeat steps 20-21 on the right. Wrap the double layer...
tailieu.vn Xem trực tuyến Tải xuống
7 Variation 1: divide in 8 8 9. slide in the overlap 11 Variation 2: divide in 16 Very difficult to form cup!. Variation 3: divide in 32. very, very difficult And the thicknes of the paper is coming in
tailieu.vn Xem trực tuyến Tải xuống
Start with 1/2 of a square or 2:1 ratio piece of paper, large paper is not needed as a 6X3 piece of foil works well. Fold the foil into sixteenths, with skin color desired on the out side.. reverse fold in the first 2 corners on each side.. pull down the pleats to form the arms.. reverse fold down the...
tailieu.vn Xem trực tuyến Tải xuống
Diagrammed by R.Glynn © July 1999. Repeat steps 5 and 6 on the other 3 sides. Fold 2 layers to the left. Fold 1 layer to the right (front and back to even up the. Fold 1 layer to the top. Valley fold the 2 small points.. Note that the lower edges are slightly above the centre crease. Squash fold...
tailieu.vn Xem trực tuyến Tải xuống
"S". The reverse "S". Make the folds "I". inside reverse folds, and "O". outside reverse folds, so the reverse "S"
tailieu.vn Xem trực tuyến Tải xuống
Fold and fold.. Fold to the crease line in the centre. In this step, only the top layer is folded.. Bring the lower edges to the middle.. Mountain fold each of the corners under as shown, at the mid-point between A and B and parallel to line B and C.. Valley fold as illustrated and crease well.. Fold down and...
tailieu.vn Xem trực tuyến Tải xuống
Martini Glass (or Birdbath). Begin with a rectangle of proportions 7 x 3. Although I designed the model for a dollar bill, I don’t recommend using one, as the process is unpleasant, and the product is small and ugly.. Begin with white side up. Divide into 1/12ths with valley-creases.. Soft valley-fold.. Mountain-fold all the way across the bottom. Valley-fold on...
tailieu.vn Xem trực tuyến Tải xuống
petal fold top flap turn model over. sqush the points to form eyes turn model over. fold the flaps in the order shown. fold the model in half swivel the nose out. open the model out and keep the nose
tailieu.vn Xem trực tuyến Tải xuống
Diagrammed by R.Glynn © February 1999. Fold the point up inside the model (you need to pull the model apart. Repeat steps 3-8 on this side. Fold the point up inside the model (much harder than step 7!). Swivel the point to the. Diagrammed by R.Glynn © February 1999 21. Repeat steps 20-21 on the right. Wrap the double layer...
tailieu.vn Xem trực tuyến Tải xuống
Swing the left half of the central diamond under the right half. This is a reverse-fold. The x-ray line is the other side of the spread.. Reverse-fold twice. Valley-fold along edge of the wrap. Tuck under where it overlaps the front of the wing.. Push down the crimp, unsinking the front of the head, and close back up.. Dent the...
tailieu.vn Xem trực tuyến Tải xuống
All Rights Reserved. This model’s design borrows from Robert Lang’s dragonfly in The Complete Book of Origami (Dover, 1988). A dollar bill makes a model 45mm long with a 63mm wingspan. For first attempt, begin with a 3x7 rectangle larger than a dollar bill.. Valley-crease the long way, mountain-crease the short way.. Rabbit-ear. Repeat on left.. Fold and unfold. Turn...
tailieu.vn Xem trực tuyến Tải xuống
©1994 by Joseph Wu Start with a coloured frog base.. Diagrammed on February 2, 1994. Do NOT repeat behind. Do NOT repeat behind.. Fold two layers to the left on the front and two layers to the right on the back.. Fold one layer to the right on the front and one layer to the left on the back.. Mountain...
tailieu.vn Xem trực tuyến Tải xuống
(enlarged) front and back. Tail...fold right to left...kite, fold left to right...repeat on left...fold sides front and back.. fold in sides (both layers)...repeat at bottom, tail will fit in here
tailieu.vn Xem trực tuyến Tải xuống
Crease into thirds Crease into 3rds again to make 9ths. Crease into 3rds once more to make 27ths. Form a small box in the centre of the paper. Repeat the procedure in step 4 to make the box taller. Repeat step 5 again to make the box 3 segments tall. Make sharp mountain creases bisecting the first flat segment at...