Có 100+ tài liệu thuộc chủ đề "phân tích kiến trúc"
tailieu.vn Xem trực tuyến Tải xuống
The objective of the following example is to mirror the windows to the south side of the west wall:. Zoom in on the windows you just arrayed.. Select the windows starting from the upper-left corner to the lower- right corner, as shown in Figure 4.24.. Make sure you do not select the wall that the windows reside in.. You do...
tailieu.vn Xem trực tuyến Tải xuống
This new function allows you to split an item like always, but now you can choose the size of the gap segment.. Now you need to add more lines to the sketch. To do this, you must leave the Split Element command and follow along using the sketch tools on the Draw panel:. On the Draw panel of the Modify...
tailieu.vn Xem trực tuyến Tải xuống
We now have five floors in the east wing alone, and we must add a layout to them. Did you already paste these elements to this level? Sometimes the top of the walls are above the level above. You can check this as well.. Now that you have added walls, doors, and windows, you can start to combine this experience...
tailieu.vn Xem trực tuyến Tải xuống
6 Placing the dimension by picking two objects. With the Aligned dimension command still running, pick the north wall again and do the following:. Pick the outside face of the northern wall.. Pick the centerline of the door, as shown in Figure 5.7, but do not press Esc, or terminate the command.. Pick the horizontal wall that ties into the...
tailieu.vn Xem trực tuyến Tải xuống
Repeat the steps for the bottom of the corridor.. Add the rest of the dimensions, as shown in Figure 5.20. This will complete the dimensioning of the corridor area.. 1 9 Placing an angular dimension means picking two walls, then a point to place the dimension.. If you would like to place the dimensions in different locations, feel free to...
tailieu.vn Xem trực tuyến Tải xuống
Revit will now give you a warning, as shown in Figure 5.32. 3 2 A Revit warning pertaining to the constraint of the walls. If you select Unconstrain, the EQ dimension will disappear as well as any constraint on the walls. Select one of the interior walls that were part of the EQ dimension string.. On the Options bar, select...
tailieu.vn Xem trực tuyến Tải xuống
Select the text.. On the Options Format panel, review the choices you have to add a leader to the text.. Click the Add Left Side Straight Leader button, as shown in Figure 5.49.. It adds a leader to the left end of the text.. By clicking the grips and moving the text around, configure the text and the leader to...
tailieu.vn Xem trực tuyến Tải xuống
You will never have a Generic 12 ″ floor in your model, so it is a good idea not to keep this floor around.. You are now in the Edit Assembly dialog. 5 Clicking the Edit button to access the structure of the floor. In the middle of the Edit Assembly dialog is a large spreadsheet-type field that is divided...
tailieu.vn Xem trực tuyến Tải xuống
The east wall has a giant gap at the bottom and an overlap at the top. Pick the Trim/Extend Single Element button from the Modify panel as shown at the top of Figure 6.16, and click the portions of the two lines you want to keep. 1 6 Picking the magenta lines in the numbered order illustrated in the figure....
tailieu.vn Xem trực tuyến Tải xuống
Notice that the fifth-level floor is not joined to any of the walls. This is because, when you pasted the floor to this level, Revit did not prompt you to cut the over- lapping geometry from the exterior walls. After the floors have been pasted, select the fifth-level floor, as shown in Figure 6.33.. On the Modify | Floors tab,...
tailieu.vn Xem trực tuyến Tải xuống
Now that the floor is selected, notice on the Modify | Floors tab that you have several choices. Click the Add Split Line button (see Figure 6.46).. Draw lines along the finished inside face of the lavatory, as shown in Figure 6.46. You will need to basically get as close to the face of the wall as possible before you...
tailieu.vn Xem trực tuyến Tải xuống
Now you can…. add a floor to your model by using the building’s footprint as a guide E. method of quickly repeating the geometry up through the building add a specific, alternate material to different parts of the floor by E. As with floors, we will also build the roof’s composition for use in schedules, quantities, and material takeoffs.. Essentially,...
tailieu.vn Xem trực tuyến Tải xuống
On the Annotate tab, click the Aligned Dimension button.. Add a dimension string starting at the exterior wall to the left and ending at the exterior wall to the right, as shown in Figure 7.10.. 1 0 Add a dimension string to the reference planes shown here.. Click the blue EQ icon. Select the roof.. Click the Add Split Line,...
tailieu.vn Xem trực tuyến Tải xuống
N O T E although you have pretty good experience with walls up to this point, Chapter 16, “Advanced Wall Topics,” is dedicated to the advanced concepts and creation of wall systems.. It’s now time to add the roof to the corridor. Because the walls our roof will bear on are now correct, the rest will be a snap!. Go...
tailieu.vn Xem trực tuyến Tải xuống
Select the west wing exterior walls, as shown in Figure 7.38.. On the Properties panel select Exterior - Brick And CMU On MTL.. Stud (No Parapet), as shown in Figure 7.38.. 3 8 Changing the walls to Exterior - Brick And CMU On MTL.. In the Project Browser, go to the West Roof floor plan.. On the Home tab, select...
tailieu.vn Xem trực tuyến Tải xuống
On the Draw panel, click the Start-End-Radius Arc button, as shown in Figure 7.53.. Draw an arc from the points shown in Figure 7.53.. the 4″ thickness is defined in the actual roof you are using. after you click Finish Edit Mode, the 4″ thickness will be added to the bottom.. 5 3 Drawing an arc, which will define the...
tailieu.vn Xem trực tuyến Tải xuống
which you can open and modify directly from either Revit Architecture, Revit Structure, or Revit MEP with absolutely no issues.. The first item we will tackle is usually the first item in the model: structural grids. Although you add structural grids line by line, you will soon discover that these grids are just as “smart” as the rest of Revit.....
tailieu.vn Xem trực tuyến Tải xuống
When you pick the wall, the grid is added. But first, pick the round blue grip and drag the bubble up past the dimensions, as shown in Figure 8.15.. Click in the bubble and rename it to A, as shown in Figure 8.16.. 1 5 Dragging the new bubble out of the wall. 1 6 The grid is now named...
tailieu.vn Xem trực tuyến Tải xuống
You will need to move some of these columns, including the four columns in the corridor intersection area. Revit will still locate these columns at a grid intersection, except it will add the offset in the column’s properties.. Zoom into the middle of the east wing at the corridor intersection.. Select the two columns at the left of the corridor,...
tailieu.vn Xem trực tuyến Tải xuống
4 7 Adding the second rod to the canopy. Mirror the rods to the other canopy. You can stay in the East eleva- tion to do so.. The next section will bring us under- ground into the foundation. Although the structural engineer will usually specify the foundation system, architects must have access to foundation tools to place concrete foundation walls...