Có 20+ tài liệu thuộc chủ đề "cách xếp giấy hay"
tailieu.vn Xem trực tuyến Tải xuống
Valley-fold in half.. Pivot at lower-left corner, valley-fold lower right corner to top edge.. Valley-fold on existing crease.. Valley-fold raw edge to folded edge.. Valley-fold halfway and unfold.. Valley-fold to half-way crease and unfold. Valley-fold edge “E” a little bit above the crease line. Hidden valley-fold makes top of leaf symetric.. Valley-fold stem into position.
tailieu.vn Xem trực tuyến Tải xuống
Mountain fold the tip. Inside reverse fold the innermost layer.. Repeat behind.. Fold the near side up.. Inside reverse fold. Repeat behind.28. Repeat behind.29. Fold the top layer down towards the head. Fold the long flap down in half, flattening the side.32. Repeat behind. Repeat behind.37. Fold the two sides of the head down to cover the crimp.. Repeat behind.40....
tailieu.vn Xem trực tuyến Tải xuống
Make a small reverse fold at the top while mountain folding the model in half.. The model will not lie flat after this step.. Round the edges along the top of the tooth and crimp the edges.
tailieu.vn Xem trực tuyến Tải xuống
Designed and diagrammed by Andy Carpenter (1998).. Wet fold the paper for best results.. Thin the face/horns &. D from step 3 are hidden by another layer of paper.. Rabbit ear the horn, thin the vertical raw edge from head to front legs, then sink fold the front legs with two layers of paper on each side.Crimp fold to form...
tailieu.vn Xem trực tuyến Tải xuống
In a traditional airplane all of the lift, is supplied by the wings, but as speed increases this puts more and more stress on the wings, the answer as was determined years ago is to use a. That is a plane or as in this case a space shuttle that maximizes the strength of structure by using the body of...
tailieu.vn Xem trực tuyến Tải xuống
This collapse is similar to the collapse that forms the centre of the sand dol-. but cannot be done in the manner shown there be- cause it generates extra creases (which detract from the transparent ef- fect of the snowflake.. Focus on one of the flaps, standing it up.. Note that the squash is symmetrical!. Result of previous step.. alternating...
tailieu.vn Xem trực tuyến Tải xuống
A first origami version of the Soma Cube was introduced by Steve Biddle in his book ‘The New Ori- gami’. Instead of describing each element step-by-step, I will therefore describe the basic elements and the methods of extending them. These methods are then presented with four of the pieces. The diagrams distinguish between a simple fold and the edge of...
tailieu.vn Xem trực tuyến Tải xuống
José Tomas Buitrago Molina Colombia (c) 1998. Diagramas: José Tomas Buitrago
tailieu.vn Xem trực tuyến Tải xuống
This model is a derivative of a model by Kunihiko Kasahara. This model works best with foil paper. Squash fold the right hand flap so that you get the results of step 3.. Fold over one layer in the front and one layer in the back.. Fold the edges in to the center and then unfold them.. Now either sink...
tailieu.vn Xem trực tuyến Tải xuống
Fold the sides up in to a rabbits ear, or make the fish base, which ever you prefer.. Reverse fold the end down from the center So that it is center in the middle of the model.. Reverse fold the flap part of the way back up.. Now with out creasing the top layers open up the bottom of the...
tailieu.vn Xem trực tuyến Tải xuống
Fold the bottom point up so that its edge hits the right corner.. Fold the horizontal edge down so that it aligns with the folded edge.. Fold the edge back up so that it aligns with a folded edge.. Fold the top flap down.. Fold the flap back up. Fold the top flap down so that its tip aligns with...
tailieu.vn Xem trực tuyến Tải xuống
4 5 Desplegar hasta. el paso 2 6. 32 Desplegar hasta el paso 29
tailieu.vn Xem trực tuyến Tải xuống
Valley fold at intersection 4. Valley fold up 5. Valley fold one flap up.. Valley fold at right angle. Valley fold up at angle. Pull out some paper.. Valley fold to the left. Valley fold back up. Slightly valley fold so that 26. Valley fold back left and 28. Valley fold front small 33. Slightly valley fold two flaps down.....
tailieu.vn Xem trực tuyến Tải xuống
Spiral Snake. The diagrams are offered for personal use any other use please contact me for permission at [email protected].. Spiral Snake page 1 of 3 http://www.kalei.com. Starting with a 1:5 paper valley fold and unfold lengthwise.. Tail Section: Valley fold corners to the center line.. Valley fold to the center line.. Completed tail section. Work the head section on the...
tailieu.vn Xem trực tuyến Tải xuống
(3) Cut along horizontal line through point C. 47x60 rectangle 1.3% difference from letter size proportion (8.5x11). (3) Bisect AB to get C. (4) Bisect DE to get F. (5) Make crease passing C and E. (6) Crease passing AF. (7) Cut along vertical line through point G. 0.1% difference from letter size proportion
tailieu.vn Xem trực tuyến Tải xuống
Square Puzzle by Marc Kirschenbaum (NY) ©1999. Pinch top edge in half.. Valley the corner to the crease.. Turn over. Valley to intersection of edges.. Precrease at the top and valley up at the bottom.. Valley the opposite edges to the creases.. Valley the corners inward. Valley up. Tuck the side into the pocket.. Repeat steps 1-5 on. Valley in...
tailieu.vn Xem trực tuyến Tải xuống
Valley fold the edges to the center, then fold the model back together.. Reverse fold the front of the model upwards.. From figure 7 until we finish the front of the model we are going to show only the front of the model.. Crimp Fold the flap Down.. Open up the inside of the head, with the thumb or finger...
tailieu.vn Xem trực tuyến Tải xuống
Squirrel (1/2) Designed by: Franti ek Grebení ek (2000) www.origami.cz. 2) Turn over. 3) Rabbit ear on the. 4) Turn over. 6) Turn over.. 9) Reverse-fold.. 11-14. Squirrel (2/2) Designed by: Franti ek Grebení ek (2000) www.origami.cz. 12) Reverse-fold. 14) Complete double-rabbit ear, following indicated. 15) Repeat steps 11-14 behind.. 16) Rabbit ear.. 17) Reverse-fold following indicated crease.. 18) Reverse-fold
tailieu.vn Xem trực tuyến Tải xuống
Fancy Model Stand 2. Variations on the Fancy Model Stand Theme. Fancy Model Stand 2 See
tailieu.vn Xem trực tuyến Tải xuống
Fold up the bill into eights so that the words Federal reserve note are visible on one side.. Valley fold the bill at the “r” in federal.. Collapse the bill back together while making the folds shown on the top layer this should result in a 90 degree turn, when collapsed. The bill should look like this, now turn the...