Có 40+ tài liệu thuộc chủ đề "xếp hình bằng giấy"
tailieu.vn Xem trực tuyến Tải xuống
6 Pointed star box - base. Begin with a square creased into quarters horizontally only crease between these lines. Inside reverse fold the double layer by lifting the top flap. Valley fold the 2 inner layers A. Fold the corner of the tab over the hidden flap to lock. Mountain fold flap behind. Assemble remaining 4 units. 6 Pointed star...
tailieu.vn Xem trực tuyến Tải xuống
1) Blintz-fold. 2) Turn over. 3) The second blintz-fold.. 4) Turn over. 5) The third blintz-fold. 6) Turn over.
tailieu.vn Xem trực tuyến Tải xuống
Viharfelho Storm-cloud. Storm-cloud. Oda-visszahajtás átlósan. Fordítsd meg a papírt!. Turn the paper over.. Váltóhajtás kifelé a modell belsejében.. Outside-reverse-fold inside the model.. Váltóhajtás kifelé ismét.. Outside-reverse-fold again.. Oda-visszahajtás.. Fold and unfold.. Oda-visszahajtás az élek találkozásánál. Fold and unfold through the intersections ( crease only until the diagonal. Oda-visszahajtás. Fold and unfold. crease only until the diagonal. Váltóhajtás meglévo éleken.. Reverse-fold...
tailieu.vn Xem trực tuyến Tải xuống
Pleat the bottom up, varying the amount will change the end result each time, but the top only goes to the center of the model.. Pleat down and again the only important landmark is the center. Then double rabbits ear the bottom of the model, note it will not be even with the bottom in most cases, wing it.. Rabits...
tailieu.vn Xem trực tuyến Tải xuống
fold Swivel head behind. Petal fold all the layers. Squash fold while folding the double layers to the centre line. Swivel head to the front. Make two inside reverse folds Tuck the point up inside the model 1. Squash fold. Round off the feet. Crimp the feet while curving the body back slightly to make the legs '3D'. Petal fold...
tailieu.vn Xem trực tuyến Tải xuống
Temate Baku Traditional 2000 Jan This model has recently been reworked by Kunihiko Kasahara from an old picture.. The picture was discovered by Kunihiko in a Japanese book about architecture.. The book dates from 1734 and thus this model is older than that.
tailieu.vn Xem trực tuyến Tải xuống
All valley folds are 120-degree planar angles.. Tuck D into pocket at bottom edge of C.. Wrap around with 120-degree planar valley folds, and tuck E into pocket on right side of front face.. The one in the front face covers the seam, but locks loosely.
tailieu.vn Xem trực tuyến Tải xuống
Then turn over the model.. Fold the top of the model into a water bomb base.. Swivel fold out the two sides at the top of the model.. Mountain fold the entire top of the model back at the point of the triangle. Turn the model over.. turn the model back over.. crese the model like shown.
tailieu.vn Xem trực tuyến Tải xuống
trapped paper to the front. Bring raw edges to the front
tailieu.vn Xem trực tuyến Tải xuống
M IDDLE S ECTION (L O W E R H ALF. T W O V IEWS O F T H E C O M P L E T E D M IDDLE S ECTION , L O W E R L O W E R H ALF . T H E L O W E R M IDDLE S ECTION....
tailieu.vn Xem trực tuyến Tải xuống
by Herman van Goubergen. Use paper which is a bit heavier than kami. (I prefer paper which is coloured on one side and foil on the other side. I fold the car with the foil inside.). Put 2 marbles in the front compartment (the engine). The car moves easier if the marbles are larger (heavier) but to minimize friction they...
tailieu.vn Xem trực tuyến Tải xuống
or “sink”) hidden. the “bird” base reverse-. the “frog” base the “preliminary” base. (or “square” base). Flapping Bird &. Flapping Bird
tailieu.vn Xem trực tuyến Tải xuống
for ny other use, please contact me for permission at [email protected].. This is roughly what you should see while the petal fold is in progress.. Repeat the maneuver on the back side.. Petal fold.. Valley fold the top two free points to the top, crease and unfold. Repeat the procedure on the back side.. Valley fold and unfold.. Open sink...
tailieu.vn Xem trực tuyến Tải xuống
Robin Glynn - November 1997. Pinch a curved mountain crease through both layers. Robin Glynn - November 1997 page 2. Fold this side flat. Form a valley fold so that the curved mountain crease lies on the straight. of the lid. Next step viewed from here. Reform the lid (steps 18 to 23) extending creases. Form the front of the...
tailieu.vn Xem trực tuyến Tải xuống
T-rex by Marc Kirschenbaum. 4.Turn over. Turn over to see the result.. 13.Mountain fold. 14.Crimp head forward.. Mountain fold legs back.. 15.Crimp head to form mouth.. Squash to form feet. 1995 Marc Kirschenbaum 60
tailieu.vn Xem trực tuyến Tải xuống
You can make the model from just about any paper (Kami, Washi, waxed, plain, etc. but the model will tend of suffer paper spread. Begin the model white side up.. 16.) Fold the flap back and forth.. 8.) Fold the sides in. 9b.) Fold the flap to the tip.. 10.) Fold into the center line.. 13.) Fold it back.. 14.)...
tailieu.vn Xem trực tuyến Tải xuống
Repeat steps 9-10 behind.. Repeat steps 12-13 on the other side.. Repeat steps 14-16 behind.. Pull out single layer.. Repeat steps 18-26 in mirror image.. Swing over flap while incorporating a reverse fold.. Repeat steps 23-26 behind.. Reverse fold.. Repeat steps 33-34 on other side.. Repeat steps 36-37 behind.. Swing back down while collapsing the top single layer outwards.. Wrap...
tailieu.vn Xem trực tuyến Tải xuống
CaterpillarMaarten van Gelder 1984 Dec Use a strip of paper 8 x 1 (24 x 3 inch or 20 x 2.5 inch will do), both sides same color. You may first try with a strip of 3 x 1. The diagrams are drawn as if folded of a 3 x 1 strip. Only the finished model is drawn as if...