Có 11+ tài liệu thuộc chủ đề "kỹ thuật đóng tàu"
tailieu.vn Xem trực tuyến Tải xuống
Để đảm bảo được yêu cầu này cần thiết phải ứng dụng các tiến bộ của khoa học kỹ thuật, tự động hóa các công đoạn sản xuất. Bài viết này bàn về một giải pháp nhằm nâng cao năng suất và chất lượng của công đoạn hàn trong công nghệ đóng tàu với robot trên đường ray.. Hiện nay,...
tailieu.vn Xem trực tuyến Tải xuống
In developing countries, in spite of the energy conservation initiatives of the 1980s (subsequent to the dramatic rise in the cost of fossil fuels), mechanization continues to increase. part of the material presented is applicable to any particular fishing situation.. In a small slow-speed vessel., the approximate distribution of energy created from the burning of fuel is shown in Figure...
tailieu.vn Xem trực tuyến Tải xuống
The shipyard absolutely undertakes responsibility on the anticorrosion of engine.. 1.3 The engine and related parts have to be stored in clean and dry indoor space (over 20 degree Celsius, below 50% of relative humidity) from arrival at shipyard to installation. However, if the engine and related parts have to be stored outside inevitably, they must be protected against the...
tailieu.vn Xem trực tuyến Tải xuống
II.5- Bản vẽ rải tôn (Shell Expansion) ...60. III.5.3- Xem bản vẽ tổng đoạn phối cảnh. III.5.5- Xem bản vẽ của nhóm kết cấu phẳng...82. III.5.6- Xuất các bản vẽ sang CAD...87. III.7.2- Mở bản vẽ sườn...93. III.7.14- Danh sách các chi tiết...119. III.7.32- Kiểm tra lại bản vẽ nhóm kết cấu phẳng...152. III.9- Sử dụng các chi tiết tiêu...
tailieu.vn Xem trực tuyến Tải xuống
NGÀY ĐẦU SÁNG. GIÁO ÁN SỨC BỀN TÀU Thời gian thực hiện: 5 tiết Lớp:VT07CM. Số giờ đã giảng:0 tiết Ngày thực hiện . UỐN TÀU TRÊN NƯỚC. Các thành phần lực tác dụng lên tàu trên nước - Điều kiện tàu cân bằng trên nước. Ổn định lớp Thời gian: 10 phút. Giới thiệu về môn học Thời gian...
tailieu.vn Xem trực tuyến Tải xuống
ĐĂNG KIỂM VIỆT NAM . ĐÓNG TÀU VÀ ĐĂNG KIỂM
tailieu.vn Xem trực tuyến Tải xuống
5V –tên gọi tắt sự liên kết của 5 cơ quan : Cục Hàng Hải Việt Nam (Vinamarine), Tổng Công Ty Hàng Hải Việt Nam (Vinalines), Tập Đoàn Công Nghiệp Tàu Thủy (Vinashin), Cục Đăng Kiểm Việt Nam (Vietnam Register - VR), Trường Đại học Hàng Hải (Vietnam Maritime University-Vimaru ) để thực hiện Chiến Lược Biển của Quốc Gia....
tailieu.vn Xem trực tuyến Tải xuống
This guide is based on these tariffs, but is made up in man- hours to assist long-term pricing. Man-hours have been used so that this book will not be ‘dated’ and can be used without encountering the problems of increases in costs over the years. Only man-hours are used in order that the compiler may assess shipyards’ charges based on...
tailieu.vn Xem trực tuyến Tải xuống
www.motorship.com. s.velden@highbur ybiz.com Tel Fax . a.topliss@highbur ybiz.com Tel Fax . e.robinson@highbur ybiz.com Tel Fax . m.skelton@highbur ybiz.com Tel Fax . UK Tel Fax www.motorship.com. Tel Fax [email protected]. j.barnes@highbur ybiz.com Tel . p.vandyck@highbur ybiz.com Tel Technical Editor. [email protected] Tel . l.reeves@highbur ybiz.com Tel . k.tolley@highbur ybiz.com . l.wall@highbur ybiz.com Tel. Repeats of articles appearing in The Motor Ship are available...
tailieu.vn Xem trực tuyến Tải xuống
Phain 3 Cac thiet bi tau. 3.1 Cac thiet bi tr6n thLrgng tang mui. 3.3 Cac thiet bi thong ham hang. 3.4 Cac thiet bi thong buong W. 3.8 Cac thiet bi tren tau du Iiich. Propeller Chin vit 9. Side light Den man (den henh trinh). Mast head light Den cot 35. Range light Den dinh cot 36. Mast...
tailieu.vn Xem trực tuyến Tải xuống
UNDERWATER WELDING. The first ever underwater welding was carried out by British Admiralty – Dockyard for sealing leaking ship rivets below the water line.. Underwater welding is an important tool for underwater fabrication works. Any repair method will require the use of underwater welding.. Underwater welding can be classified as 1) Wet Welding. In wet welding the welding is performed...